Ductile Iron 4 Inch Groove Type OS&Y Rising Stem Gate Valve For a rising stem valve, the stem will go up while opening the valve and move down when you close the valve. You can see in the image. In inside screw design, the threaded portion of the stem is in contact with the flow medium and when you open the valve, handwheel rise with the stem. Whereas in the case of outside screw design, the only smooth portion is exposed to the flow medium and stem will rise above the handwheel. This type of valve is also known as OS & Y valve.  OS & Y means outside steam and York.   Products Features - Precision-machined valve stem, reduces operating torque. - Non-toxic powder epoxy resin spraying on botn inside and outside of the valve to enhance corrosion resistance and improve water quality. - The valve plate is covered with rubber both inside and outside to guaranteed good sealing. It has strong connection to avoid fall off after long-term use. - Thrust bearings reduce frictional resistance and reduce operating torque.   Product Parameter   DN 50 65 80 100 125 150 200 250 300 350 400 D 57 60 76 178 322 114 133 159 219 273 325 377 426 140 165 A1 14.5 14.5 14.5 16 16 16 19 19 19 25 25 BA 9.5 9.5 9.5 9.5 9.5 9.5 13 13 13 13 13 C 2.2 2.2 2.2 2.2 2.2 2.2 2.5 2.5 3.3 3.3 5.5 Z81X     L 145 180 180 180 200 240 275 325 355     H 325 455 455 455   500 620 750 800     D0 180 200 200 200   240 320 320 400    

8 Inch Flange Type Signal Gate Valve The signal gate valve is mainly used in the pipeline of the fire water system as a function of opening and intercepting the fluid in the pipeline, and converting the opening and closing working state into an electric signal through the signal device. The elastic seat sealing gate valve signal gate valve encapsulating the whole valve disc to generate a deformation compensation effect to achieve a good sealing effect, overcome the general gate valve sealing failure, water leakage, and rust phenomenon, more effective saving installation space.   It's mainly composed by the signal device, valve body, valve cover, disc assembly, stem, stem nut, hand wheel and other components. The annunciator is mainly composed of a transmission gear, a transmission rod and a micro switch. Gate Valve Applications Gate valves are used in almost all fluid services such as air, fuel gas, feedwater, steam, lube oil, hydrocarbon, and all most any services. Some special gate valve is used in slurry and powder product also such as knife gate valve Advantages of Gate Valve Gate valve provides good pressure drop during operation  Most of the gate valve can be used as bi-directional They are suitable for high pressure and temperature application and required less maintenance    Product Parameter   DN L H H1 W C n-D E T F 50 178 233 123 203 125 4-φ19 165 19 3 65 190 233 93 203 145 4-φ19 185 19 3 80 203 270 100 203 160 8-φ19 200 20 3 100 229 322 110 203 180 8-φ19 220 20 3 125 254 355 125 280 210 8-φ19 250 20 3 150 267 401 143 280 240 8-φ19 285 20 3 200 292 516 170 330 295 8-φ23 340 21 3 250 330 638 203 382 355 12-φ23 406 26 3 300 356 717 230 420 410 12-φ28 460 26 4 350 381 844 260 420 470 16-φ28 520 26.5 4 400 406 935 282 420 525 16-φ31 580 28 4

PN16 Non Rising Stem Groove Type Gate Valve DN100 There is no upward movement of the stem in a non-rising stem type. The valve disk is threaded internally. The disc travels along the stem like a nut when the stem is rotated. You can see the image. In this type of valve, stem threads are exposed to the flow medium. Therefore, this design is used where space is limited to allow linear stem movement, and the flow medium does not cause erosion, corrosion, or wear and tear to stem material.  This type of valve also known as insider screw valve. Gate Valve Applications Gate valves are used in almost all fluid services such as air, fuel gas, feedwater, steam, lube oil, hydrocarbon, and all most any services. Some special gate valve is used in slurry and powder product also such as knife gate valve Advantages of Gate Valve Gate valve provides good pressure drop during operation  Most of the gate valve can be used as bi-directional They are suitable for high pressure and temperature application and required less maintenance

Ductile Iron Groove Type Signal 6 Inch Water Gate Valve The signal gate valve is mainly used in the pipeline of the fire water system as a function of opening and intercepting the fluid in the pipeline, and converting the opening and closing working state into an electric signal through the signal device. The elastic seat sealing gate valve signal gate valve encapsulating the whole valve disc to generate a deformation compensation effect to achieve a good sealing effect, overcome the general gate valve sealing failure, water leakage, and rust phenomenon, more effective saving installation space.   It's mainly composed by the signal device, valve body, valve cover, disc assembly, stem, stem nut, hand wheel and other components. The annunciator is mainly composed of a transmission gear, a transmission rod and a micro switch. Gate Valve Applications Gate valves are used in almost all fluid services such as air, fuel gas, feedwater, steam, lube oil, hydrocarbon, and all most any services. Some special gate valve is used in slurry and powder product also such as knife gate valve Advantages of Gate Valve Gate valve provides good pressure drop during operation  Most of the gate valve can be used as bi-directional They are suitable for high pressure and temperature application and required less maintenance

Worm Gear Ductile Iron Resilient Seated Butterfly Valve Butterfly valve is a valve that isolates or regulates the flow of a fluid. The closing mechanism is a disk that rotates. This Resilient Seated Butterfly Valve is double flanged design which can be used for dead-end service.   Products Features Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they cost less than other valve designs, and are lighter weight so they need less support. The disc is positioned in the center of the pipe. A rod passes through the disc to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow.   Product Parameter Size Range: 2" - 8" (50mm - 200mm) Body Style: Double Flanged Temperature Range: -20°C to 150°C) Pressure Ratings: Bidirectional Bubble-tight Shutoff: to 250 psi (17.2 Bar) Body (CWP): 250 psi (17.2 Bar) Body Materials: Ductile Iron Disc Materials: Ductile Iron Seat Materials: Bonded EPDM Applications: Wastewater, Seawater

Ductile Iron Y Type Strainer This product is designed for remove foreign matter from pipe lines and provides protection for pumps, meters, valves, and other similar mechanical equipment, which is called as Strainer. "Y" Type Strainers are named after their shape and normally used for course filtration. But with large filtration area can be used with fine mesh also.   The Strainer improves the clearance in the medium, and prolongs the life of valves; protect expensive pumps, meters and other equipments.  A Y-strainer can be installed in either a horizontal or vertical position (Downward flow) with the screen elementpointing downward. This allows the strainer screen to collect material in the strainer at the lowest point of the screen.

Ductile Iron Flange Silent Check Valve Silent Check Valves are designed to prevent water hammer in multi-story buildings and for use in vertical turbine pump installations when pumping from a well to an elevated reservoir. Silent Check Valves are recommended for commercial and industrial HVAC applications such as heating systems and condensate return lines. The valve closes silently, is low in cost, reliable and requires no regular maintenance. When the pump stops, the spring forces disc closed against slight pump head at zero velocity which results in silent closure.

One Way Non Return Swing Check Valve Rubber disc check valve is mainly composed of body, cover and rubber disc three parts.Rubber disc is made by steel plate, steel bar and the reinforced nylon fabric substrate.This valve is usually installed in the outlet of the pump or inlet of water pool to prevent the water backflow and avoid damages to the pump caused by the water hammer phenomenon. The water flow in water supply or irritation networks often starts or stops abruptly causing hydraulic hammer shock, the main factor for breakage and damages of the pumps and pipes. The check valve with the rubber blocking eliminates the pump and network destruction risks because it receives and absorbs all the created high pressure functioning like the shock absorber of an automobile. The rubber disc check valve is designed to provide the best possible protection to pump installations and water networks.   Advantages: Absorbs part of the hydraulic surge waves Silent operation Smooth liquid flow Little maintenance required Applications: Irrigation Water supply networks Pump stations

Water Pressure Relief Valve for Fire Fighting This valve is used for the high building fore-fighting system,To prevent the pipeline and equipment damage due to overpressure. The body uses full passage streamline design, of a small fluid resistance and a heavy flow. This valve can be used as either a pressure releasing or holding valve.  when used as the former, it can release the pressure surpassing the safe value set with the pilot valve and keep the pressure inside of the pipeline below the safe value to prevent system against danger due to an excessively high water pressure;while used as the latter,it can keep the upstream water supply pressure of the main valve over some set value,this is because water supply to the downstream can not be done,unless the upstream is higher than the set value,in order to make sure of he upstream water supply pressure of the main valve.

Water Pressure Release Valve for Fire Fighting The valve consists of the main valve and outside installed control pilot valve, mainly installed in the bypass of the protected water supply system in the building, guarantee the pressure of the main valve upstream water supply zone, when the pressure in the water supply pipe exceeds the pressure set by the pressure releasing valve, the pressure releasing valve is switched on to prevent pipeline and equipment from damage by pressure exceeding. This valve is mainly used in pressure releasing of the fire test circulation system in high-rise buildings, is the upgrade replacement product of the spring safety valve.   Features: 1)Reasonable and novel structure, reasonable use of the hydraulic principle to control. 2)Long service life. 3)Valve clack quick opening and slow closure, no water hammer impacting. 4)High sensitivity, safe pressure discharge. 5)Stable operation, no noise.

Pre-action Systems Fire Alarm Check Valve Pre-action sprinkler systems are specialized for use in locations where accidental activation is especially undesirable, such as in museums with rare art works, manuscripts, or books; and data centers, for protection of computer equipment from accidental water discharge.   Pre-action systems are hybrids of wet, dry, and deluge systems, depending on the exact system goal.    Model Norminal Diameter   (mm) Working Pressure   (MPa) Drive Time(s) ZSFY-100 DN100 1.2~1.6 <15 ZSFY-150 DN150 1.2~1.6 <15 ZSFY-200 DN200 1.2~1.6 <15

Wet Pipe System Fire Alarm Check Valve The alarm check valve is a water flow alarm device designed for vertical installation in the main supply to a wet pipe sprinkler system. When a flow of water from the system equals or exceeds that of a single sprinkler, the valve is to actuate a fire alarm. Model Norminal Diameter (mm) Working Pressure (MPa) Drive Time(s) ZSFZ-100 DN100 1.2~1.6 <15 ZSFZ-125 DN125 1.2~1.6 <15 ZSFZ-150 DN150 1.2~1.6 <15 ZSFZ-200 DN200 1.2~1.6 <15 Technical Data     Body Material Ductile Iron  Pipe Material Stainless Steel 304 Ball Valve Material Brass Fire Alarm Bell Material Stainless Steel 304 Retarder Material Stainless Steel 304 Pipe & Elbow Stainless Steel 304 Size (mm) DN100,DN125,DN150,DN200 Production Standard GB5135.5~2003

Diaphragm Style Fire Alarm Deluge Valve Price Deluge Valve is known as a system control valve in a deluge system, used for fast application of water in a spray system. Deluge valve protects areas such as power transformer installation, storage tank, conveyor protection and other industrial application etc. With the addition of foaming agent they do protect aircraft hanger and inflammable liquid fire.   Model Norminal Diameter (mm) Working Pressure   (MPa) Drive Time(s) S-ZSFM-100 DN100 1.2~1.6 <15 S-ZSFM-125 DN125 1.2~1.6 <15 S-ZSFM-150 DN150 1.2~1.6 <15   Technical Data Body Material Ductile Iron  Pipe Material Stainless Steel 304 Ball Valve Material Brass Fire Alarm BellMaterial Stainless Steel 304 Size (mm) DN100,DN125,DN150,DN200,DN250 Production Standard GB5135.5~2003 Solenoid Valve Voltage DC24V Application fire fighting, foam system, fire protection system,fire sprinkler system Operation solenoid control, hydraulic, electric actuation

Ductile Iron Water Seal Thread Gate Valve PN16 A gate valve, also known as a sluice valve, is a valve that opens by lifting a barrier (gate) out of the path of the fluid. Gate valves require very little space along the pipe axis and hardly restrict the flow of fluid when the gate is fully opened. The gate faces can be parallel but are most commonly wedge-shaped (in order to be able to apply pressure on the sealing surface).   Gate valves are used to shut off the flow of liquids rather than for flow regulation. When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low flow resistance.   Gate Valve Applications Gate valves are used in almost all fluid services such as air, fuel gas, feedwater, steam, lube oil, hydrocarbon, and all most any services. Some special gate valve is used in slurry and powder product also such as knife gate valve Advantages of Gate Valve Gate valve provides good pressure drop during operation  Most of the gate valve can be used as bi-directional They are suitable for high pressure and temperature application and required less maintenance

2 Inch Brass Oblique Fire Valve Storz Fire Valve is a connector to fire water supply with the valve interface, used for factory, warehouse, high-rise buildings, public buildings and ship, normally installed in fire hydrant box, with fire hoses and water gun or wait for equipment supporting the fire equipment .   Type: Fire Valve Storz Model: WFHV - B50 Material: Brass Inlet interface: 50 mm / 2 inch Rated working pressure: 1.6 Mpa For water and foam mixed liquid only Standard: Manufacture and certified to DIN 14461    Name Indoor fire hydrant Body Material Brass Valve Rod Material Brass Size 50mm Packing Carton with pallet Delivery time 15-20 days OEM Avaliable Original Made In China

Single Head Storz Coupling Spanner Wrench Storz coupling Spanner wrenches are widely used, making tightly close or open couplings convenient in life for fire fighting equipments.   Item Code Coupling Size Material SP1525 1.5"~2.5" Galvanized iron SP2504 2.5"~4" Galvanized iron   Product Features Material: Cast iron with black rubber jacket Size available: 1-1/2”~2-1/2”, 2.5”~4” Spanners are used for loosening hose-to-hose connections or hose-to-appliances and hardware